Store Logo
 
Rinnai Tankless HeatersNatural Gas TanklessPropane Gas TanklessConcentric Vent/RL SeriesConcentric Vent/RU SeriesRinnai Ultra SeriesRinnai Luxury SeriesRinnai Value SeriesAccessoriesInstallation ToolsIsolator Valve (Flush Kits)Scale Control SystemsCirc Pumps & EquipmentRinnai Direct Vent HeatersGroundwater Temp Map
 
Why Choose UsNewsPhotosRebatesRinnai Extended WarrantyContact UsMy AccountFeatured ProductsF.A.Q.
 

 Official PayPal Seal

 

FedEx will obtain a signature from any
person 
at least 21 years old (government-issued
photo identification required) at the delivery
address. If no one is at the address, FedEx
will reattempt delivery. 

 

 

 

 

 

 

 

 

TO PAY WITH  CLICK PayPal
 
 BUTTON RIGHT THEN CHECKOUT

 

Pay with a debit or credit card, or PayPal Credit

 
 
 

            Speak to a Master Plumber

 
0 items

Rinnai Filter

Rinnai Filter
Rinnai Filter
  
Rinnai Filter

 Our Price: $15.00

 Cleaning Rinnai Water Heater Input Water Filter

 

On the center pipe beneath the water heater is a barrel shaped screen filter. This may be

removed and cleaned by running water into the open end of the filter. If you are

experiencing water flow or performance issues, a clogged filter could be the cause.

Location of water filter housing on bottom of heater unit.

                                              

                                     

Procedure:

1. Shut off the cold water input to the water heater. A shut off valve should be installed below the filter housing.
NOTE: If you cannot locate the shutoff valve, either shut off main structure supply or do not proceed without a qualified service professional.

2. Turn on a hot water tap to drain off existing water in unit.

3. Remove filter by unscrewing plug located directly below the cabinet on the center pipe (see above diagram). This plug is about the same size as a U.S. Quarter. (Be prepared for a small amount of back-flowing water to drain from the unit. If a large amount of pressure appears to be on this line while unscrewing, STOP immediately and return the plug to its original state—contact a qualified service professional to assist.)

4. Clean debris from filter by running under fresh water. NOTE: Do not use cleaners or solvents which could contaminate your water supply. Food grade vinegar or citric acid can be used if needed.

5. Replace filter and tighten finger tight.

6. Restore flow by turning on the water input valve. (Insure no water is dripping from filter housing.)

 If frequent cleaning is required, consider an in-line filter or water softener on the incoming cold water supply. 


 
 
Product Rating
Ratings
Be the first to review this product

Customers who bought this product also purchased

1 Gallon Flow-Aide
1 Gallon Flow-Aide
MSB-C1
MSB-C1
18" Vertical Discharge Termination for RU,RC & HP Series
18" Vertical Discharge Termination for RU,RC & HP Series
45 Degree Elbow (2) for RU,RC & HP Series
45 Degree Elbow (2) for RU,RC & HP Series
Flat Roof Flashing
Flat Roof Flashing
MSB-M Controller
MSB-M Controller

 Cleaning Rinnai Water Heater Input Water Filter

 

On the center pipe beneath the water heater is a barrel shaped screen filter. This may be

removed and cleaned by running water into the open end of the filter. If you are

experiencing water flow or performance issues, a clogged filter could be the cause.

Location of water filter housing on bottom of heater unit.

                                              

                                     

Procedure:

1. Shut off the cold water input to the water heater. A shut off valve should be installed below the filter housing.
NOTE: If you cannot locate the shutoff valve, either shut off main structure supply or do not proceed without a qualified service professional.

2. Turn on a hot water tap to drain off existing water in unit.

3. Remove filter by unscrewing plug located directly below the cabinet on the center pipe (see above diagram). This plug is about the same size as a U.S. Quarter. (Be prepared for a small amount of back-flowing water to drain from the unit. If a large amount of pressure appears to be on this line while unscrewing, STOP immediately and return the plug to its original state—contact a qualified service professional to assist.)

4. Clean debris from filter by running under fresh water. NOTE: Do not use cleaners or solvents which could contaminate your water supply. Food grade vinegar or citric acid can be used if needed.

5. Replace filter and tighten finger tight.

6. Restore flow by turning on the water input valve. (Insure no water is dripping from filter housing.)

 If frequent cleaning is required, consider an in-line filter or water softener on the incoming cold water supply. 


 
 
 
Copyright © 2016 Wholesale Tankless Online Store

Privacy Policy          Return Policy          Customer Service          Shipping Policy          Terms of Service 
Site Secured By: Website Guardian